Your browser is not supported. For the best experience, you should upgrade to a modern browser with improved speed and security.

80% AFUE 112000 Btuh Gas-Fired Hot Water Boiler

Item: BW3AAN000112
MFR: BW3AAN000112

Store Inventory

Sign in to see real-time inventory at the stores closest to you.
What’s the price?
Sign in for pricing.

Frequently Bought Together

Best Sellers

Piping Valves & Pumps

About This Product

Product Info

Description

BW3AAN000112
B = Boiler
W = Water Type of System
3 = Induced Draft/Electronic Combustion/Ignition
A = Model Code
A = 110 to 125 Volts 60 Hz Electrical
N = Natural Gas Fuel
000 = Cooling
112 = 112,500 Max input Btuh

Model BW3 Gas-Fired Induced Combustion Water Boilers are the answer to energy-efficient residential hydronic heating. These boilers provide quality design in a small, compact unit easily installed in a basement, garage, or utility room. They can be installed on a combustible floor when an optional combustible floor base is used. The BW3 boilers are CSA certified for use with natural gas and are field convertible for use with propane gas when a factory-authorized conversion kit is used.

FEATURES
RANGE OF CAPACITIES
The BW3 boiler is available in sizes from 42,500 to 225,000.
COMPLETELY PACKAGED
Each boiler is completely assembled, including all controls (except thermostat and expansion tank). All necessary wiring is factory installed, except for the circulator pump. The boiler is ready for gas, water, room thermostat, and electrical connections.
THERMAL-PIN, CAST-IRON SECTIONS
These sections speed heat transfer from the flue gases to the boiler water with faster thermostat response, providing greater comfort and economy. Maximum heat is produced at a lower level on the thermal-pin sections, leading to peak efficiency.
INTEGRAL DRAFT
These boilers incorporate an integral draft system to simplify installation. No external draft diverter is needed.
TITANIUM COMPOSITE BURNERS
Provide quiet operation, corrosion resistance and improved combustion efficiency. Propane convertible – with accessory kit.
CONTROLS
An automatic gas valve and continuous pilot or intermittent pilot provide quiet, dependable operation of the burners. Factory-installed safety components assure protection against overheating and pressure build-up. A factory-authorized accessory kit is available for protection against low water operation where required by local code. The circulator is pre-wired with 6-ft. of BX conduit for easy installation for supply-side plumping.
INSULATED CASING
The casing is fully insulated with fiberglass for maximum operating efficiency and economy.
AUTOMATIC VENT DAMPER
The BW3 boiler is an induced draft design and does not require or use an automatic vent damper. These boilers are category 1 for venting purpose.
SECTIONS TESTED
Each section is hydrostatically tested to 50 psig. Individual sections are tested to 125 psig at factory. Assembled sections are tested to 75 psig at the factory. The maximum allowable pressure is 50 psig for hot water boilers.
WARRANTY
The cast-iron sections are covered by a non-prorated 20-year warranty on the entire assembly. All other parts are covered by a 5-year limited warranty.
Warning: this product contains a chemical known to the State of California to cause cancer. P65Warnings.ca.gov

Specifications

Weight317 Pounds (lbs)
Width17.5 Inches (In)
Height29 Inches (In)
Country of OriginUSA
Length23.25 Inches (In)
AFUE83%
BrandCarrier,Bryant
BTU Input112500
BTU Output94000
CompositionThermal-Pin, Cast-Iron Heat Exchanger, Titanium Composite Burners, Insulated Casing, Automatic Vent Damper
Connection Size1 1/4"
Connection TypeElectronic
Cycle/Hertz60 Hz
FinishFine Grain Cast Iron Sections, Stainless/Titanium Alloy Burners
Fuel TypeNatural Gas
Full Load Amps0.76
Gas ConnectionFPT
Gas TypeNatural Gas/LP
Heating Capacity94000
Ignition TypeElectronic
Maximum Fuse Size15
PhaseSingle
Prop 65Yes
Temperature Range60°F to 320°F (15.5°C to 160°C)
TierComfort,Legacy™
Voltage115 VAC
Warranty OfferedYes

Documents

Equipment Part List

Loading...